Engineered Carbon Fiber Solutions, Direct from Our Factory.
We are the manufacturer. Carbon fiber sheets, tubes, rods, and precision CNC components are made in our own factory for industrial equipment, engineered assemblies, and repeat OEM supply. No middleman, no trading company markup.
Made in Our Factory, Ready for What Comes Next
Seven product lines, each with its own page and drawing-based production route. Start from the product closest to your part, or send a drawing and we will route it for you.
Carbon Fiber Sheets
Sheets and plates with custom thickness, weave, finish, and CNC processing options.
Carbon Fiber Tubes
Pultruded and roll-wrapped tubes for UAV, robotics, industrial, and OEM applications.
Carbon Fiber Rods
High-stiffness solid rods for precision equipment, structures, and engineered assemblies.
Carbon Fiber Profiles
Pultruded profiles for repeatable, lightweight structural and industrial applications.
Forged Carbon Fiber Sheets
CNC-ready forged carbon sheets for machined parts with a marbled forged look.
Telescopic Boom Poles
Lightweight telescopic carbon fiber poles for location sound and field recording.
Also in the range: 3K Matte Roll-Wrapped Carbon Fiber Tube → and the 8mm Carbon Fiber Rod →
Our Own Production Floor. A Visible Process.
Everything happens under our own roof, from machining and material processing to final inspection and export packing. Because we make it ourselves, we control quality, lead time, and cost at every stage.
Material Loading
Carbon fiber roll stock loaded and fed on our own production floor, so material handling stays in-house from the first metre.
Layup & Forming
Layup and forming on dedicated worktables, where sheet and part geometry are set before curing.
Autoclave Curing
Heat and pressure curing in our own autoclaves, for consistent, fully consolidated parts.
CNC Cutting
Waterjet and CNC cutting in our own workshop, direct from your drawing files.
Made for Demanding Applications
Choose the material form and processing route from the real application, not from a generic material claim.
Aerospace / UAV
Frames, payload structures, panels, and supports where mass and stiffness decide performance.
Robotics & Automation
Lightweight arms, frames, and moving structures for repeatable, high-cycle equipment.
Automotive
Panels, brackets, and structural parts where weight reduction matters.
Industrial Equipment
Profiles, tubes, and machined parts for engineered assemblies and OEM supply.
Sports / Recreation
Rods, tubes, and components built for strength-to-weight performance.
We Are the Factory Behind Your Carbon Fiber Parts
Justar is a carbon fiber manufacturer, not a trading company. We produce sheets, tubes, rods, and profiles in-house and machine them to your drawings, so OEM teams deal directly with the people who make the parts, from material selection to production-ready delivery.
Factory direct
You buy from the manufacturer. No agent, no trading markup, and pricing set on our own production floor.
In-house engineering support
Our own engineers review drawings, geometry, finish, and production needs with you before we cut material.
Own CNC machining
Precision machining for plates, profiles, and custom components, done in our own workshop.
Global export delivery
Export coordination, protective packing, and overseas delivery handled by the factory itself.
Bring Us Your Next Carbon Fiber Challenge
Share your drawing, specification, or application requirements and talk directly to the factory. Tell us the geometry, quantity, and finish you need, and our own team will reply with a manufacturability check and next steps.
Email: [email protected]
WhatsApp: +86 17076247612
Website: justarcb.com
This sample form opens your email client with the inquiry pre-filled to [email protected]. On the live site it will post directly to the Justar inbox.
Carbon Fiber Products, Direct from the Factory
Seven product lines produced in-house: sheets, tubes, rods, profiles, forged sheets, and finished boom poles. Every line supports custom dimensions and drawing-based production. Send a specification or a drawing and the factory quotes it directly.
Carbon Fiber Sheet
Flat sheets and plates in plain and twill weave, matte or gloss, ready as stock material or CNC cut to your drawing.
Carbon Fiber Tube
Pultruded and roll-wrapped tubes for frames, arms, shafts, and structural assemblies across UAV, robotics, and industry.
3K Matte Roll-Wrapped Tube
Roll-wrapped tube with a visible 3K weave and a low-glare matte finish, for parts that are seen as well as loaded.
Carbon Fiber Rod
Solid pultruded rods for linkages, supports, and precision assemblies. Cut to length, with the 8mm size on its own page.
Carbon Fiber Profile
Pultruded angles, channels, and custom cross-sections for repeatable structural builds and OEM supply.
CNC-Ready Forged Carbon Sheet
Forged carbon fiber sheet stock made to be machined: plates, covers, and parts with the forged marbled pattern.
Telescopic Microphone Boom Pole
A finished product, not raw tube: a lightweight telescopic boom pole for location sound, built from our own carbon tube.
8mm Carbon Fiber Rod
The established 8mm size, kept on its own indexed page. Solid carbon fiber rod, cut to your required length.
Custom CNC Parts
None of the standard lines fit? Send the drawing. We machine custom carbon fiber parts from our own sheet and tube stock.
Not sure which product form fits?
Tell us the application, the load direction, and the space the part has to fit. The factory will recommend sheet, tube, rod, or profile and quote it.
Carbon Fiber Sheet
Flat carbon fiber sheets and plates produced in our own factory, supplied as stock material or CNC machined to your drawing. The starting point for panels, plates, covers, and structural parts where stiffness per weight decides the design.
- Plain weave and 2×2 twill weave options
- Matte or gloss surface finish
- Custom sheet sizes and thicknesses on request
- CNC cutting, drilling, and edge finishing in-house
- Prototype quantities through to repeat production
Options to specify
| Weave | Plain weave or 2×2 twill |
|---|---|
| Finish | Matte or gloss |
| Size & thickness | Quoted to your drawing or dimensions |
| Processing | As-cut sheet, or CNC machined part with holes, slots, and profiles |
Typical uses
- UAV and robotics panels, frames, and mounting plates
- Industrial equipment covers, guards, and brackets
- Automotive panels and interior structural parts
- Base stock for custom CNC machined components
Need the forged look instead of a woven surface? See the CNC-ready forged carbon fiber sheet.
Send the drawing, get a factory quote
Dimensions, thickness, weave, finish, and quantity are all we need to quote. Email [email protected].
Related products
Carbon Fiber Tube
Carbon fiber tubes in two production routes: pultruded for straight, cost-efficient structural runs, and roll-wrapped for higher strength and a finished woven surface. Made in our factory and cut to the lengths your assembly needs.
- Pultruded tubes for straight structural applications
- Roll-wrapped tubes with woven outer surface
- Round tubes as the standard form, other forms on request
- Cut to length, with machining available in-house
- Telescoping tube combinations for extendable assemblies
Which route fits your part?
- Pultruded: fibers run along the tube, best for straight members loaded mainly in tension, compression, and bending along the axis. The economical choice for long structural runs.
- Roll-wrapped: woven fabric wrapped and cured, better hoop strength and a visible weave finish. The choice when the tube is clamped, joined, or on show.
Typical uses
- UAV arms, frames, and landing structures
- Robotics arms and automation linkages
- Industrial shafts, supports, and machine frames
- Telescopic poles and extendable equipment
Looking for the woven matte version specifically? See the 3K matte roll-wrapped tube. Building a finished pole? See the telescopic boom pole.
Quote a tube in one message
Inner and outer diameter, length, quantity, and whether it will be clamped or bonded. That is enough for the factory to quote.
Related products
3K Matte Roll-Wrapped Carbon Fiber Tube
A roll-wrapped tube with a 3K woven outer layer and a matte finish. It is the tube to choose when the surface is part of the product: visible weave, no gloss reflections, and the hoop strength that wrapping gives over a plain pultruded tube.
- 3K woven outer layer with a clear, even weave pattern
- Matte finish that cuts glare on camera and in hand
- Roll-wrapped construction for clamping and joining
- Cut to length, telescoping sets available
- Used in our own telescopic boom poles
Why roll-wrapped, why matte
Roll-wrapping lays woven fabric around the tube, so the wall resists crushing at clamps and fittings better than unidirectional pultrusion. The 3K outer layer gives the classic carbon checker pattern, and the matte finish keeps it readable under studio and location lighting instead of reflecting it.
Typical uses
- Microphone boom poles and camera support tubes
- Visible frame tubes on UAV and sports equipment
- Handles, grips, and hand-held equipment tubes
- Any assembly where the tube surface stays exposed
Specify it in one line
Outer diameter, wall or inner diameter, finished length, and quantity. We confirm the telescoping fit if sections need to slide.
Related products
Carbon Fiber Rod
Solid carbon fiber rods for assemblies that need stiffness and low weight in a simple, dependable form. A rod is the right answer when the part works along its length: pushing, pulling, bracing, or locating, without the cost of a hollow section.
- Solid carbon fiber construction, light and stiff along the axis
- Cut to your required length before shipping
- Smooth, consistent surface for bonding and fitting
- Prototype quantities through to repeat OEM supply
Where rods earn their place
- Linkages, pushrods, and control runs in UAV and robotics
- Bracing and support members in lightweight structures
- Pins, shafts, and locating elements in precision equipment
- Sports and recreation builds that need a stiff, light spar
How to order
Tell us the diameter, the finished length, and the quantity. If the rod will be bonded, clamped, or machined at the ends, mention it in the inquiry and we will confirm the fit before production.
The most requested size has its own page: 8mm carbon fiber rod →
Quote a rod in one message
Diameter, length, quantity. Email [email protected] or message us on WhatsApp.
Related products
Carbon Fiber Profile
Pultruded carbon fiber profiles: constant cross-sections produced in long, repeatable runs. Angles, channels, and flat bars that let you build stiff, light structures without machining every member from plate.
- Constant cross-section along the full length
- Angles, channels, flat bars, and custom sections on request
- Cut to length, with drilling and machining in-house
- Repeatable supply for OEM production runs
Why a profile instead of a machined part
Pultrusion pulls fiber through a heated die, so the cross-section is the same at every point of the run. For frames, rails, and structural members that repeat across a product, that means consistent geometry, less machining, and a lower cost per metre than cutting each piece from sheet.
Typical uses
- Equipment frames and structural rails
- Edge members and stiffeners for large panels
- Industrial assemblies that repeat across a product line
- Lightweight structures replacing aluminium sections
Send the cross-section
A sketch or drawing of the section, the length per piece, and the total quantity. Custom sections are quoted against tooling and volume.
Related products
CNC-Ready Forged Carbon Fiber Sheet
Forged carbon fiber sheet stock made to go straight onto the CNC. Chopped fiber compression-moulded into plate gives the marbled forged pattern, and the sheet is supplied flat and consistent so it can be machined into finished parts without extra preparation.
- Forged marbled pattern, no two parts look identical
- Supplied as sheet stock, ready for CNC machining
- Matte or gloss finish after machining
- We can supply the sheet, or machine the parts for you in-house
Forged vs woven sheet
A woven sheet shows a regular checker pattern and its strength follows the weave directions. A forged sheet uses chopped fiber in random orientation, which gives the marbled look and more uniform behaviour across the plate, useful for small machined parts loaded from several directions.
Typical uses
- Covers, plates, and housings with a premium forged look
- Automotive and consumer product trim parts
- Small machined components, brackets, and mounts
- Prototype parts machined from stock sheet
Prefer the classic woven surface? See the standard carbon fiber sheet.
Sheet only, or finished parts?
Say which one in the inquiry. For finished parts, attach the drawing and the finish you want, and the factory machines them in-house.
Related products
Carbon Fiber Telescopic Microphone Boom Pole
A finished boom pole for location sound, built from our own roll-wrapped carbon fiber tube. It exists for one reason: a boom operator holds it overhead for hours, so every gram saved at the pole is fatigue saved on set, while the stiffness keeps handling noise and flex down.
- Built from our own carbon fiber tube, made in the same factory
- Telescopic sections that extend for reach and collapse for transport
- Light enough for long handheld takes, stiff enough to stay quiet
- For film, TV, and field recording crews and OEM audio brands
Why carbon fiber for a boom pole
A boom pole is a lever held at arm's length. Carbon fiber gives the stiffness of a much heavier metal pole at a fraction of the weight, so the microphone stays where it is pointed, the pole flexes less when it moves, and the operator can work longer takes. That is why location sound moved to carbon, and why we build this pole from the same tube we sell.
Ordering
Tell us the extended reach you need, the collapsed length your kit allows, and the quantity. For OEM orders, tell us your branding and packaging requirements in the same message and we will quote the finished product, not just the tube.
The tube itself is also sold on its own: 3K matte roll-wrapped tube →
Ask for the current configuration
Sections, locks, and cable options are confirmed per order. Message the factory and we will send the configuration that matches your reach and quantity.
Related products
8mm Carbon Fiber Rod
The 8mm solid carbon fiber rod: the most requested rod size, kept on its own page. Solid carbon fiber, stiff and light along its length, and cut to the length your assembly needs before it ships.
- 8mm diameter solid carbon fiber rod
- Cut to your required length
- For linkages, supports, and precision assemblies
- Order on its own or with other rod and tube sizes
Where the 8mm rod is used
- Pushrods and linkages in UAV and model engineering
- Supports and bracing in lightweight structures
- Shafts and locating elements in small equipment
- Replacement and upgrade parts in sports equipment
How to order
State the length per piece and the quantity. If the ends will be bonded into fittings or clamped, say so in the inquiry and we will confirm the finish before cutting. For other diameters, see the main carbon fiber rod page.
Quote the 8mm rod
Length and quantity are all we need. Email [email protected].
Carbon Fiber Applications
Carbon fiber earns its cost where weight, stiffness, or fatigue life is the limiting factor. These are the application areas our factory supplies, and the product form that usually fits each one.
Aerospace / UAV
Frames, arms, payload structures, and panels. Mass saved in the structure is payload or flight time gained. Usual forms: roll-wrapped tube, sheet, and CNC machined parts.
Robotics & Automation
Moving arms, end effectors, and frames that cycle all day. Lighter moving parts mean smaller motors and faster cycles. Usual forms: tube, profile, and machined sheet parts.
Automotive
Panels, brackets, and structural parts where weight reduction matters, plus forged carbon trim where the look is part of the product. Usual forms: sheet and forged sheet, CNC machined.
Industrial Equipment
Profiles, tubes, and machined parts for engineered assemblies and repeat OEM supply, replacing metal sections where corrosion or weight is a problem. Usual forms: pultruded tube and profile.
Audio & Field Production
Boom poles and support tubes held or carried all day. Stiffness keeps the microphone steady, low weight keeps the operator working. Usual form: telescopic boom pole built from roll-wrapped tube.
Sports & Recreation
Rods, tubes, and components built for strength-to-weight performance in equipment that is swung, carried, or ridden. Usual forms: rod, tube, and custom machined parts.
Protective Equipment
Carbon fiber also appears in protective applications, where layered composite structures absorb and spread impact energy. We keep a technical guide on the subject.
Your application is not listed?
Most of our work starts as a drawing for an application nobody has catalogued. Send it anyway. If carbon fiber is the wrong material for the job, we will say so before you spend anything.
Manufacturing Capabilities
One factory, the full route from raw material form to finished, inspected, export-packed part. Because production is in-house, a drawing review, a machining question, and a delivery date all come from the same people who make the part.
Production Lines
Sheet and material production lines under our own roof, so the material form and the finished part are controlled together.
Autoclave Curing
Autoclave curing capacity in-house, for heat and pressure consolidation of sheets and moulded parts.
CNC Machining
Cutting, drilling, and profiling of sheet, forged sheet, tube, and profile stock in our own workshop, direct from your drawing files.
Quality Inspection
Dimensional checks against the drawing before packing. Parts that do not match the drawing do not leave the factory.
On the Production Floor
Real photos from the Justar production floor: the hall, the lines, layup, curing, and cutting. This is where every sheet, tube, and machined part on this site is made.
What we can take on
- Drawing-based production: send a drawing or CAD description, get a manufacturability check before any commitment
- Prototypes and first samples ahead of a production decision
- Repeat OEM supply of the same part across orders
- Material-form advice: sheet vs tube vs rod vs profile for your load case
- Combined orders across product lines in one shipment
How an order runs
- 1. Inquiry: drawing, dimensions, quantity to [email protected] or WhatsApp
- 2. Factory review: we check geometry, material form, and finish, and raise any issue before quoting
- 3. Quotation: priced by the factory, no trading markup in between
- 4. Production & inspection: made and checked in-house
- 5. Packing & delivery: export-packed and shipped
Put the factory to the test
Send one drawing, even a difficult one. The review costs nothing and tells you quickly whether we are the right maker for the part.
Talk Directly to the Factory
No agents and no trading desk in between. Your inquiry goes to the Justar factory team and is answered by the people who will make the part.
For drawings, specifications, and formal quotations. Attach the drawing to the first message if you have one.
For quick questions, photos of the part you need matched, and order follow-ups during the project.
Website
Product pages carry the specification route for each line. Start there if you are still choosing a material form.
Send an Inquiry
The fastest quote comes from three things: what the part is, its key dimensions or a drawing, and how many you need. The form prepares an email with those details to [email protected].
What happens next: the factory reviews the geometry and material choice, raises any manufacturability issue, then replies with the quotation and the next step. No obligation from asking.
This sample form opens your email client with the inquiry pre-filled. On the live site it will post directly to the Justar inbox.
Exploring the Future of Protection: Advancements in Carbon Fiber Armor
Protective equipment has always been a trade between protection and weight. Metal plate protects well and exhausts the wearer. Carbon fiber composites entered this field because they offer a different trade: high stiffness and strength at a fraction of the weight, with energy behaviour that can be tuned through the layup.
Why carbon fiber suits protective structures
A carbon fiber composite is not a single material but a structure: fibers carry the load, the resin holds them in position, and the way layers are stacked decides how the part responds. In a protective panel that layering matters, because an impact is not one force in one direction. A well-designed layup spreads the load across the panel instead of letting it concentrate at the strike point.
- Low weight for the stiffness achieved, which decides whether protection is actually worn
- Layered construction that can be tuned for the expected impact direction
- Corrosion resistance in field and marine environments
- Formability into curved panels that follow the body or the vehicle
Where the development is heading
Current work in composite protection focuses on hybrid layups, combining carbon fiber with other fibers and core materials so each layer does the job it is best at, and on manufacturing routes that make curved, consistent panels repeatable at production volume rather than one-off prototypes. As those routes mature, composite protection moves from specialist equipment toward wider use in vehicles, industrial safety, and personal protective equipment.
The honest limits
Carbon fiber is not the answer to every protection problem. It is brittle compared with metals, its performance depends entirely on correct design and manufacture, and any protective product still has to be tested and certified against the standard for its intended use. Material choice is the start of that process, not a substitute for it.
Justar manufactures carbon fiber sheets, tubes, rods, and machined components for industrial and OEM applications. If your project involves composite panels or structures, the factory can discuss material forms and machining routes for your design.
Working on a composite structure?
Talk to the factory about sheet stock and machined components for your design.