多页样本 · 供确认 justarcb.com 重建样本:首页 + 产品总页 + 7 个产品页 + 应用 / 能力 / 联系页 + Resources 博客(总页 + 9 篇文章),另保留 8mm 杆页与护甲指南页。 确认后再上线,现站不动。
Carbon Fiber Factory · Direct Manufacturer

Engineered Carbon Fiber Solutions, Direct from Our Factory.

We are the manufacturer. Carbon fiber sheets, tubes, rods, and precision CNC components are made in our own factory for industrial equipment, engineered assemblies, and repeat OEM supply. No middleman, no trading company markup.

Factory Direct PricingIn-House ProductionCarbon Fiber TubesCarbon Fiber SheetsCNC Machined PartsWorldwide Export
CNC machining a carbon fiber plate at the Justar factory
Factory Direct
You deal with the manufacturer, not a trader
In-House CNC
Machining done in our own workshop
OEM & Prototype
From first samples to repeat production
Worldwide Export
Protective packing for overseas delivery
Inside Our Factory

Our Own Production Floor. A Visible Process.

Everything happens under our own roof, from machining and material processing to final inspection and export packing. Because we make it ourselves, we control quality, lead time, and cost at every stage.

Panorama of the main production hall at the Justar factory, with carbon fiber production lines on both sides
JUSTAR FACTORY · MAIN PRODUCTION HALL
Carbon fiber roll stock loaded onto the production line at the Justar factory
01

Material Loading

Carbon fiber roll stock loaded and fed on our own production floor, so material handling stays in-house from the first metre.

Layup workshop at the Justar factory, with carbon fiber material laid out on worktables
02

Layup & Forming

Layup and forming on dedicated worktables, where sheet and part geometry are set before curing.

Autoclave with its door open at the Justar factory
03

Autoclave Curing

Heat and pressure curing in our own autoclaves, for consistent, fully consolidated parts.

CNC waterjet cutting a carbon fiber sheet at the Justar factory
04

CNC Cutting

Waterjet and CNC cutting in our own workshop, direct from your drawing files.

See Full Capabilities →

Applications

Made for Demanding Applications

Choose the material form and processing route from the real application, not from a generic material claim.

Aerospace / UAV

Frames, payload structures, panels, and supports where mass and stiffness decide performance.

Robotics & Automation

Lightweight arms, frames, and moving structures for repeatable, high-cycle equipment.

Automotive

Panels, brackets, and structural parts where weight reduction matters.

Industrial Equipment

Profiles, tubes, and machined parts for engineered assemblies and OEM supply.

Sports / Recreation

Rods, tubes, and components built for strength-to-weight performance.

All Applications →

About Justar · The Factory

We Are the Factory Behind Your Carbon Fiber Parts

Justar is a carbon fiber manufacturer, not a trading company. We produce sheets, tubes, rods, and profiles in-house and machine them to your drawings, so OEM teams deal directly with the people who make the parts, from material selection to production-ready delivery.

Factory direct

You buy from the manufacturer. No agent, no trading markup, and pricing set on our own production floor.

In-house engineering support

Our own engineers review drawings, geometry, finish, and production needs with you before we cut material.

Own CNC machining

Precision machining for plates, profiles, and custom components, done in our own workshop.

Global export delivery

Export coordination, protective packing, and overseas delivery handled by the factory itself.

Carbon fiber sheet production line running at the Justar factory
Start a Project

Bring Us Your Next Carbon Fiber Challenge

Share your drawing, specification, or application requirements and talk directly to the factory. Tell us the geometry, quantity, and finish you need, and our own team will reply with a manufacturability check and next steps.

Email: [email protected]
WhatsApp: +86 17076247612
Website: justarcb.com

This sample form opens your email client with the inquiry pre-filled to [email protected]. On the live site it will post directly to the Justar inbox.

Home / Products
Products · /products/

Carbon Fiber Products, Direct from the Factory

Seven product lines produced in-house: sheets, tubes, rods, profiles, forged sheets, and finished boom poles. Every line supports custom dimensions and drawing-based production. Send a specification or a drawing and the factory quotes it directly.

Carbon fiber sheets
/products/carbon-fiber-sheet/

Carbon Fiber Sheet

Flat sheets and plates in plain and twill weave, matte or gloss, ready as stock material or CNC cut to your drawing.

View product →
Carbon fiber tubes
/products/carbon-fiber-tube/

Carbon Fiber Tube

Pultruded and roll-wrapped tubes for frames, arms, shafts, and structural assemblies across UAV, robotics, and industry.

View product →
3K matte roll-wrapped carbon fiber tube
/products/3k-matte-roll-wrapped…/

3K Matte Roll-Wrapped Tube

Roll-wrapped tube with a visible 3K weave and a low-glare matte finish, for parts that are seen as well as loaded.

View product →
Carbon fiber rods
/products/carbon-fiber-rod/

Carbon Fiber Rod

Solid pultruded rods for linkages, supports, and precision assemblies. Cut to length, with the 8mm size on its own page.

View product →
Carbon fiber profiles
/products/carbon-fiber-profile/

Carbon Fiber Profile

Pultruded angles, channels, and custom cross-sections for repeatable structural builds and OEM supply.

View product →
Forged carbon fiber sheet machined parts
/products/cnc-ready-forged…/

CNC-Ready Forged Carbon Sheet

Forged carbon fiber sheet stock made to be machined: plates, covers, and parts with the forged marbled pattern.

View product →
Carbon fiber telescopic microphone boom pole
/products/carbon-fiber-telescopic…/

Telescopic Microphone Boom Pole

A finished product, not raw tube: a lightweight telescopic boom pole for location sound, built from our own carbon tube.

View product →
8mm carbon fiber rod
/carbon-fiber-rod-8mm/

8mm Carbon Fiber Rod

The established 8mm size, kept on its own indexed page. Solid carbon fiber rod, cut to your required length.

View product →
CNC machining a custom carbon fiber part
CUSTOM · DRAWING-BASED

Custom CNC Parts

None of the standard lines fit? Send the drawing. We machine custom carbon fiber parts from our own sheet and tube stock.

Send a drawing →

Not sure which product form fits?

Tell us the application, the load direction, and the space the part has to fit. The factory will recommend sheet, tube, rod, or profile and quote it.

Home / Products / Carbon Fiber Sheet
/products/carbon-fiber-sheet/

Carbon Fiber Sheet

Flat carbon fiber sheets and plates produced in our own factory, supplied as stock material or CNC machined to your drawing. The starting point for panels, plates, covers, and structural parts where stiffness per weight decides the design.

  • Plain weave and 2×2 twill weave options
  • Matte or gloss surface finish
  • Custom sheet sizes and thicknesses on request
  • CNC cutting, drilling, and edge finishing in-house
  • Prototype quantities through to repeat production
Carbon fiber sheets in different thicknesses

Options to specify

WeavePlain weave or 2×2 twill
FinishMatte or gloss
Size & thicknessQuoted to your drawing or dimensions
ProcessingAs-cut sheet, or CNC machined part with holes, slots, and profiles

Typical uses

  • UAV and robotics panels, frames, and mounting plates
  • Industrial equipment covers, guards, and brackets
  • Automotive panels and interior structural parts
  • Base stock for custom CNC machined components

Need the forged look instead of a woven surface? See the CNC-ready forged carbon fiber sheet.

Send the drawing, get a factory quote

Dimensions, thickness, weave, finish, and quantity are all we need to quote. Email [email protected].

Related products

Home / Products / Carbon Fiber Tube
/products/carbon-fiber-tube/

Carbon Fiber Tube

Carbon fiber tubes in two production routes: pultruded for straight, cost-efficient structural runs, and roll-wrapped for higher strength and a finished woven surface. Made in our factory and cut to the lengths your assembly needs.

  • Pultruded tubes for straight structural applications
  • Roll-wrapped tubes with woven outer surface
  • Round tubes as the standard form, other forms on request
  • Cut to length, with machining available in-house
  • Telescoping tube combinations for extendable assemblies
Carbon fiber tubes in different diameters

Which route fits your part?

  • Pultruded: fibers run along the tube, best for straight members loaded mainly in tension, compression, and bending along the axis. The economical choice for long structural runs.
  • Roll-wrapped: woven fabric wrapped and cured, better hoop strength and a visible weave finish. The choice when the tube is clamped, joined, or on show.

Typical uses

  • UAV arms, frames, and landing structures
  • Robotics arms and automation linkages
  • Industrial shafts, supports, and machine frames
  • Telescopic poles and extendable equipment

Looking for the woven matte version specifically? See the 3K matte roll-wrapped tube. Building a finished pole? See the telescopic boom pole.

Quote a tube in one message

Inner and outer diameter, length, quantity, and whether it will be clamped or bonded. That is enough for the factory to quote.

Related products

Home / Products / 3K Matte Roll-Wrapped Tube
/products/3k-matte-roll-wrapped-carbon-fiber-tube/

3K Matte Roll-Wrapped Carbon Fiber Tube

A roll-wrapped tube with a 3K woven outer layer and a matte finish. It is the tube to choose when the surface is part of the product: visible weave, no gloss reflections, and the hoop strength that wrapping gives over a plain pultruded tube.

  • 3K woven outer layer with a clear, even weave pattern
  • Matte finish that cuts glare on camera and in hand
  • Roll-wrapped construction for clamping and joining
  • Cut to length, telescoping sets available
  • Used in our own telescopic boom poles
3K matte roll-wrapped carbon fiber tubes

Why roll-wrapped, why matte

Roll-wrapping lays woven fabric around the tube, so the wall resists crushing at clamps and fittings better than unidirectional pultrusion. The 3K outer layer gives the classic carbon checker pattern, and the matte finish keeps it readable under studio and location lighting instead of reflecting it.

Typical uses

  • Microphone boom poles and camera support tubes
  • Visible frame tubes on UAV and sports equipment
  • Handles, grips, and hand-held equipment tubes
  • Any assembly where the tube surface stays exposed

Specify it in one line

Outer diameter, wall or inner diameter, finished length, and quantity. We confirm the telescoping fit if sections need to slide.

Related products

Home / Products / Carbon Fiber Rod
/products/carbon-fiber-rod/

Carbon Fiber Rod

Solid carbon fiber rods for assemblies that need stiffness and low weight in a simple, dependable form. A rod is the right answer when the part works along its length: pushing, pulling, bracing, or locating, without the cost of a hollow section.

  • Solid carbon fiber construction, light and stiff along the axis
  • Cut to your required length before shipping
  • Smooth, consistent surface for bonding and fitting
  • Prototype quantities through to repeat OEM supply
Solid carbon fiber rods in graduated diameters

Where rods earn their place

  • Linkages, pushrods, and control runs in UAV and robotics
  • Bracing and support members in lightweight structures
  • Pins, shafts, and locating elements in precision equipment
  • Sports and recreation builds that need a stiff, light spar

How to order

Tell us the diameter, the finished length, and the quantity. If the rod will be bonded, clamped, or machined at the ends, mention it in the inquiry and we will confirm the fit before production.

The most requested size has its own page: 8mm carbon fiber rod →

Quote a rod in one message

Diameter, length, quantity. Email [email protected] or message us on WhatsApp.

Related products

Home / Products / Carbon Fiber Profile
/products/carbon-fiber-profile/

Carbon Fiber Profile

Pultruded carbon fiber profiles: constant cross-sections produced in long, repeatable runs. Angles, channels, and flat bars that let you build stiff, light structures without machining every member from plate.

  • Constant cross-section along the full length
  • Angles, channels, flat bars, and custom sections on request
  • Cut to length, with drilling and machining in-house
  • Repeatable supply for OEM production runs
Pultruded carbon fiber profiles

Why a profile instead of a machined part

Pultrusion pulls fiber through a heated die, so the cross-section is the same at every point of the run. For frames, rails, and structural members that repeat across a product, that means consistent geometry, less machining, and a lower cost per metre than cutting each piece from sheet.

Typical uses

  • Equipment frames and structural rails
  • Edge members and stiffeners for large panels
  • Industrial assemblies that repeat across a product line
  • Lightweight structures replacing aluminium sections

Send the cross-section

A sketch or drawing of the section, the length per piece, and the total quantity. Custom sections are quoted against tooling and volume.

Related products

Home / Products / CNC-Ready Forged Carbon Fiber Sheet
/products/cnc-ready-forged-carbon-fiber-sheet/

CNC-Ready Forged Carbon Fiber Sheet

Forged carbon fiber sheet stock made to go straight onto the CNC. Chopped fiber compression-moulded into plate gives the marbled forged pattern, and the sheet is supplied flat and consistent so it can be machined into finished parts without extra preparation.

  • Forged marbled pattern, no two parts look identical
  • Supplied as sheet stock, ready for CNC machining
  • Matte or gloss finish after machining
  • We can supply the sheet, or machine the parts for you in-house
CNC machined parts from forged carbon fiber sheet

Forged vs woven sheet

A woven sheet shows a regular checker pattern and its strength follows the weave directions. A forged sheet uses chopped fiber in random orientation, which gives the marbled look and more uniform behaviour across the plate, useful for small machined parts loaded from several directions.

Typical uses

  • Covers, plates, and housings with a premium forged look
  • Automotive and consumer product trim parts
  • Small machined components, brackets, and mounts
  • Prototype parts machined from stock sheet

Prefer the classic woven surface? See the standard carbon fiber sheet.

Sheet only, or finished parts?

Say which one in the inquiry. For finished parts, attach the drawing and the finish you want, and the factory machines them in-house.

Related products

Home / Products / Telescopic Microphone Boom Pole
/products/carbon-fiber-telescopic-microphone-boom-pole/

Carbon Fiber Telescopic Microphone Boom Pole

A finished boom pole for location sound, built from our own roll-wrapped carbon fiber tube. It exists for one reason: a boom operator holds it overhead for hours, so every gram saved at the pole is fatigue saved on set, while the stiffness keeps handling noise and flex down.

  • Built from our own carbon fiber tube, made in the same factory
  • Telescopic sections that extend for reach and collapse for transport
  • Light enough for long handheld takes, stiff enough to stay quiet
  • For film, TV, and field recording crews and OEM audio brands
Carbon fiber telescopic microphone boom pole

Why carbon fiber for a boom pole

A boom pole is a lever held at arm's length. Carbon fiber gives the stiffness of a much heavier metal pole at a fraction of the weight, so the microphone stays where it is pointed, the pole flexes less when it moves, and the operator can work longer takes. That is why location sound moved to carbon, and why we build this pole from the same tube we sell.

Ordering

Tell us the extended reach you need, the collapsed length your kit allows, and the quantity. For OEM orders, tell us your branding and packaging requirements in the same message and we will quote the finished product, not just the tube.

The tube itself is also sold on its own: 3K matte roll-wrapped tube →

Ask for the current configuration

Sections, locks, and cable options are confirmed per order. Message the factory and we will send the configuration that matches your reach and quantity.

Related products

Home / Products / 8mm Carbon Fiber Rod
/carbon-fiber-rod-8mm/ · Retained page

8mm Carbon Fiber Rod

The 8mm solid carbon fiber rod: the most requested rod size, kept on its own page. Solid carbon fiber, stiff and light along its length, and cut to the length your assembly needs before it ships.

  • 8mm diameter solid carbon fiber rod
  • Cut to your required length
  • For linkages, supports, and precision assemblies
  • Order on its own or with other rod and tube sizes
8mm carbon fiber rod among graduated solid rod diameters

Where the 8mm rod is used

  • Pushrods and linkages in UAV and model engineering
  • Supports and bracing in lightweight structures
  • Shafts and locating elements in small equipment
  • Replacement and upgrade parts in sports equipment

How to order

State the length per piece and the quantity. If the ends will be bonded into fittings or clamped, say so in the inquiry and we will confirm the finish before cutting. For other diameters, see the main carbon fiber rod page.

Quote the 8mm rod

Length and quantity are all we need. Email [email protected].

Home / Applications
Applications · /carbon-fiber-application/

Carbon Fiber Applications

Carbon fiber earns its cost where weight, stiffness, or fatigue life is the limiting factor. These are the application areas our factory supplies, and the product form that usually fits each one.

Aerospace / UAV

Frames, arms, payload structures, and panels. Mass saved in the structure is payload or flight time gained. Usual forms: roll-wrapped tube, sheet, and CNC machined parts.

Tubes → · Sheets →

Robotics & Automation

Moving arms, end effectors, and frames that cycle all day. Lighter moving parts mean smaller motors and faster cycles. Usual forms: tube, profile, and machined sheet parts.

Profiles → · Rods →

Automotive

Panels, brackets, and structural parts where weight reduction matters, plus forged carbon trim where the look is part of the product. Usual forms: sheet and forged sheet, CNC machined.

Forged sheets →

Industrial Equipment

Profiles, tubes, and machined parts for engineered assemblies and repeat OEM supply, replacing metal sections where corrosion or weight is a problem. Usual forms: pultruded tube and profile.

Profiles → · Tubes →

Audio & Field Production

Boom poles and support tubes held or carried all day. Stiffness keeps the microphone steady, low weight keeps the operator working. Usual form: telescopic boom pole built from roll-wrapped tube.

Boom poles →

Sports & Recreation

Rods, tubes, and components built for strength-to-weight performance in equipment that is swung, carried, or ridden. Usual forms: rod, tube, and custom machined parts.

8mm rod → · Tubes →

Protective Equipment

Carbon fiber also appears in protective applications, where layered composite structures absorb and spread impact energy. We keep a technical guide on the subject.

Read the carbon fiber armor guide →

Your application is not listed?

Most of our work starts as a drawing for an application nobody has catalogued. Send it anyway. If carbon fiber is the wrong material for the job, we will say so before you spend anything.

Talk to the factory →

Home / Capabilities
Capabilities · /capabilities/

Manufacturing Capabilities

One factory, the full route from raw material form to finished, inspected, export-packed part. Because production is in-house, a drawing review, a machining question, and a delivery date all come from the same people who make the part.

Carbon fiber production line running at the Justar factory
01

Production Lines

Sheet and material production lines under our own roof, so the material form and the finished part are controlled together.

Row of autoclaves in the curing hall at the Justar factory
02

Autoclave Curing

Autoclave curing capacity in-house, for heat and pressure consolidation of sheets and moulded parts.

Large CNC cutting table with carbon fiber material at the Justar factory
03

CNC Machining

Cutting, drilling, and profiling of sheet, forged sheet, tube, and profile stock in our own workshop, direct from your drawing files.

Dimensional inspection of carbon fiber parts
04

Quality Inspection

Dimensional checks against the drawing before packing. Parts that do not match the drawing do not leave the factory.

Inside the Justar Factory

On the Production Floor

Real photos from the Justar production floor: the hall, the lines, layup, curing, and cutting. This is where every sheet, tube, and machined part on this site is made.

What we can take on

  • Drawing-based production: send a drawing or CAD description, get a manufacturability check before any commitment
  • Prototypes and first samples ahead of a production decision
  • Repeat OEM supply of the same part across orders
  • Material-form advice: sheet vs tube vs rod vs profile for your load case
  • Combined orders across product lines in one shipment

How an order runs

  • 1. Inquiry: drawing, dimensions, quantity to [email protected] or WhatsApp
  • 2. Factory review: we check geometry, material form, and finish, and raise any issue before quoting
  • 3. Quotation: priced by the factory, no trading markup in between
  • 4. Production & inspection: made and checked in-house
  • 5. Packing & delivery: export-packed and shipped

Put the factory to the test

Send one drawing, even a difficult one. The review costs nothing and tells you quickly whether we are the right maker for the part.

Home / Contact
Contact · /contact/

Talk Directly to the Factory

No agents and no trading desk in between. Your inquiry goes to the Justar factory team and is answered by the people who will make the part.

Email

For drawings, specifications, and formal quotations. Attach the drawing to the first message if you have one.

Write an Email

WhatsApp

+86 17076247612

For quick questions, photos of the part you need matched, and order follow-ups during the project.

Website

justarcb.com

Product pages carry the specification route for each line. Start there if you are still choosing a material form.

Browse Products

Send an Inquiry

The fastest quote comes from three things: what the part is, its key dimensions or a drawing, and how many you need. The form prepares an email with those details to [email protected].

What happens next: the factory reviews the geometry and material choice, raises any manufacturability issue, then replies with the quotation and the next step. No obligation from asking.

This sample form opens your email client with the inquiry pre-filled. On the live site it will post directly to the Justar inbox.

Home / Applications / Carbon Fiber Armor Guide
Technical Guide · Retained page

Exploring the Future of Protection: Advancements in Carbon Fiber Armor

Protective equipment has always been a trade between protection and weight. Metal plate protects well and exhausts the wearer. Carbon fiber composites entered this field because they offer a different trade: high stiffness and strength at a fraction of the weight, with energy behaviour that can be tuned through the layup.

Why carbon fiber suits protective structures

A carbon fiber composite is not a single material but a structure: fibers carry the load, the resin holds them in position, and the way layers are stacked decides how the part responds. In a protective panel that layering matters, because an impact is not one force in one direction. A well-designed layup spreads the load across the panel instead of letting it concentrate at the strike point.

  • Low weight for the stiffness achieved, which decides whether protection is actually worn
  • Layered construction that can be tuned for the expected impact direction
  • Corrosion resistance in field and marine environments
  • Formability into curved panels that follow the body or the vehicle

Where the development is heading

Current work in composite protection focuses on hybrid layups, combining carbon fiber with other fibers and core materials so each layer does the job it is best at, and on manufacturing routes that make curved, consistent panels repeatable at production volume rather than one-off prototypes. As those routes mature, composite protection moves from specialist equipment toward wider use in vehicles, industrial safety, and personal protective equipment.

The honest limits

Carbon fiber is not the answer to every protection problem. It is brittle compared with metals, its performance depends entirely on correct design and manufacture, and any protective product still has to be tested and certified against the standard for its intended use. Material choice is the start of that process, not a substitute for it.

Justar manufactures carbon fiber sheets, tubes, rods, and machined components for industrial and OEM applications. If your project involves composite panels or structures, the factory can discuss material forms and machining routes for your design.

Working on a composite structure?

Talk to the factory about sheet stock and machined components for your design.

Home / Resources
Resources · /resources/

Guides & Articles from the Factory Floor

Buying guides and technical explainers written around the questions customers actually ask before they order: how to specify a sheet, which tube route fits, what 3K means, what drives the price. Every guide ends at the product page it belongs to.

Stacked woven carbon fiber sheets
BUYING GUIDE · SHEETS

Carbon Fiber Sheet Buying Guide

Weave, finish, thickness, and processing: the decisions that decide whether a sheet order comes back right, and what to put in the inquiry so the factory quotes the sheet you actually need.

Read the guide →
Carbon fiber tubes in graduated diameters
COMPARISON · TUBES

Roll-Wrapped vs Pultruded Carbon Fiber Tube

Two ways of making a carbon tube, two different strength profiles. How each is made, where each one wins, and how to choose when the tube will be clamped, joined, or loaded along its length.

Read the comparison →
Solid carbon fiber rods in graduated diameters
BUYING GUIDE · RODS

Carbon Fiber Rod Guide

When a solid rod beats a hollow tube, how rods are made, and what to specify: diameter, finished length, end use, and the fitting questions worth settling before you order.

Read the guide →
3K woven carbon fiber surface with a checker pattern
EXPLAINER · MATERIALS

What Does 3K Mean in Carbon Fiber Sheet?

3K is a tow size, not a quality grade. What the number actually counts, how it changes the look, drape, and handling of a sheet, and when 3K is the right choice.

Read the explainer →
CNC machining a carbon fiber plate
PROCESS · MACHINING

CNC Machining Carbon Fiber

Carbon fiber machines well, but not like metal. Tooling, dust extraction, edge quality, and the drawing details that make a machined part come out right the first time.

Read the guide →
Carbon fiber production line at the Justar factory
BUYING GUIDE · COST

Carbon Fiber Cost and Pricing Guide

No two quotes are alike, because the cost sits in the material form, the layup, the machining time, and the quantity. Where the money actually goes, and how to keep a project economical.

Read the guide →
Carbon fiber UAV frame seen from above
APPLICATIONS · UAV

Carbon Fiber in Drones and UAV

Airframes are where carbon fiber earns its keep: every gram in the structure is a gram off payload or flight time. The parts drones use, and the material forms they are made from.

Read the article →
Layup workshop at the Justar factory
EXPLAINER · PROCESS

Wet Carbon vs Dry Carbon

Two routes to a carbon fiber part with very different consistency, cost structure, and finish. What the terms actually mean in the workshop, and how to tell which route a part was made by.

Read the explainer →
Carbon fiber sheets used in layered composite structures
TECHNICAL GUIDE · PROTECTION

Advancements in Carbon Fiber Armor

How layered carbon fiber composites behave in protective structures, where the development is heading, and the honest limits of the material in protection applications.

Read the guide →

Reading because you have a part to make?

Skip ahead: send the drawing or the dimensions and the factory will route it to the right material form and quote it directly.

Home / Resources / Carbon Fiber Sheet Buying Guide
Buying Guide · Resources

Carbon Fiber Sheet Buying Guide

A carbon fiber sheet looks like a simple product: a flat plate of woven fiber. In practice, most sheet orders that disappoint do so because of a decision that was never made explicit, a finish assumed instead of specified, a thickness chosen from a photo, processing left to guesswork. This guide walks through the decisions in the order the factory works through them, so your inquiry covers them the first time.

Stacked woven carbon fiber sheets showing plain and twill surfaces and layered edges
Sheet stock, stacked. The weave pattern and the layered edge are the two things to check when you compare sheet offers.

1. Start from the part, not the sheet

A sheet is almost never the end product. It becomes a panel, a plate, a cover, a frame member. So the first question is what the finished part has to do: carry load in one direction or several, be seen or be hidden, be bolted, bonded, or clamped. A decorative cover and a structural mounting plate can start from the same-looking sheet and need completely different layups. Tell the factory the application, and the rest of the specification gets easier.

2. Choose the weave for the job

The two standard weaves are plain weave and 2×2 twill. Plain weave crosses every tow over and under its neighbour, which makes a stable, even sheet that handles predictably and shows a small, regular checker. Twill crosses in a diagonal pattern, which drapes better over curves, handles slightly more kindly at the edges, and shows the diagonal pattern most people picture as "carbon fiber". Neither is stronger in any simple sense; the choice is about drape, appearance, and how the sheet will be cut and used.

3. Pick the finish honestly

Gloss shows the weave at full contrast and reads as a finished, premium surface. Matte cuts reflections, hides fingerprints and minor handling marks, and suits parts that sit under lights or cameras. The finish is a surface decision, not a structural one, so choose it for the environment the part will live in. If the sheet will be machined and the machined faces are what people see, say so, because the finish conversation changes.

Carbon fiber sheets in different thicknesses ready for cutting
Thickness is a design decision. Stiffness rises fast with thickness, so a small increase often does the work of a much heavier redesign.

4. Thickness: buy stiffness, not habit

Sheet stiffness climbs steeply as thickness grows, much faster than weight does. That cuts both ways: a sheet slightly thicker than the minimum can transform a flexing panel, and a sheet thicker than the job needs is money and mass carried for nothing. If you are replacing a metal plate, do not copy its thickness across; carbon fiber is not a one-for-one substitute. Give the factory the load case or the part it replaces, and let the thickness be quoted against the job.

5. Decide the processing before you order

The cheapest sheet is the one you cut yourself, and for simple rectangles that can be the right call. But the moment the part has holes, slots, cut-outs, or a profile, factory CNC processing usually wins: the cuts are made from your drawing, edges are finished, and you receive parts instead of a cutting project. Ordering sheet "to be machined later" without saying so can also mean the sheet arrives without the machining allowances your process needs. State plainly which of these you are buying: raw sheet, cut blanks, or finished machined parts.

6. What to put in the inquiry

  • The part the sheet becomes, and what it has to carry or do
  • Sheet size and thickness, or the finished part dimensions
  • Weave (plain or 2×2 twill) and finish (matte or gloss)
  • Processing: raw sheet, cut to size, or CNC machined to a drawing
  • Quantity, including whether this is a prototype run or repeat supply

With those five points covered, a sheet quote is a short conversation instead of a long one, and the sheet that arrives is the sheet the design assumed.

Ready to specify a sheet?

The product page carries the options in one place: weave, finish, sizes, and in-house CNC processing, quoted by the factory.

Home / Resources / Roll-Wrapped vs Pultruded Tube
Comparison · Resources

Roll-Wrapped vs Pultruded Carbon Fiber Tube

Two carbon fiber tubes can look nearly identical on a shelf and behave very differently in an assembly. The difference is how they were made, and it decides how the tube handles clamping, joining, and loads that do not run straight along its length. This comparison explains both routes plainly, so the choice is made on the application rather than on habit or price alone.

Carbon fiber tubes in graduated diameters laid side by side
Same shelf, different construction. Diameter and length are easy to compare; the manufacturing route is what changes the behaviour.

How a pultruded tube is made

In pultrusion, continuous fibers are pulled through resin and then through a heated die that sets the tube's shape. Because the fibers are pulled straight, they end up running along the length of the tube, all in one direction. That is exactly what a straight structural member wants: stiffness and strength along the axis, produced continuously and economically in long runs. The trade-off is that very little fiber runs around the circumference, so the wall has less resistance to being crushed, split, or pried open at a fitting.

How a roll-wrapped tube is made

Roll-wrapping starts with woven fabric. Pre-impregnated fabric is wrapped around a mandrel in layers, compacted, and cured, then the mandrel is removed and the tube is finished. The weave means fibers run both along the tube and around it, and additional layers can be oriented for the loads expected. The result costs more to make than a pultruded tube, and in return the wall resists crushing at clamps, holds fittings and bonded joints more kindly, and presents the woven carbon surface most people expect to see.

Roll-wrapped carbon fiber tubes with a visible woven surface standing in a row
The wrapped surface. The visible weave is not decoration added afterwards; it is the outer layer of the structure itself.

Where each one wins

  • Choose pultruded for long, straight members loaded mainly along their length: structural runs, rails, and supports where the ends are supported rather than crushed, and where cost per metre matters across a production run.
  • Choose roll-wrapped where the tube will be clamped, drilled, bonded into fittings, or telescoped; where it takes handling and side loads; or where the tube stays visible and the woven finish is part of the product.
  • Telescoping sets are roll-wrapped territory: sections must slide, lock, and take clamp pressure at the joints, which is precisely what the wrapped wall is built for.

The mistake to avoid

The common failure is a pultruded tube specified for a clamped joint because it was the cheaper line on the quote. The tube performs exactly as made, and the joint crushes or splits the wall, and the saving is spent again on the replacement. The reverse mistake exists too: roll-wrapped tube bought for a long, simple structural run pays for hoop strength the part never uses. Match the route to the joint and the load, and either tube is the right tube.

What to tell the factory

Inner and outer diameter, finished length, quantity, and above all how the tube will be joined and loaded: clamped, bonded, drilled, telescoped, or simply supported. With the joining method stated, the factory will confirm the route, and if the cheaper route genuinely fits the job, that is the one that gets quoted.

Both routes, one product page

Pultruded and roll-wrapped tubes are quoted side by side on the tube page. State the joining method and the factory confirms which route your part needs.

Home / Resources / Carbon Fiber Rod Guide
Buying Guide · Resources

Carbon Fiber Rod Guide

The carbon fiber rod is the simplest product in the range: a solid round section of fiber and resin, nothing hollow, nothing to configure. That simplicity is its strength. A rod does one job, carrying load along its length, and does it in a form that is easy to cut, bond, and fit. This guide covers when a rod is the right answer, when it is not, and what to specify.

Solid carbon fiber rods
Solid, not hollow. A rod trades the tube's weight advantage for simplicity, crush resistance, and easy fitting at the ends.

Rod or tube: the honest comparison

For the same outside diameter, a tube is lighter and, diameter for diameter, stiffer in bending, because its material sits further from the centre. So why does the rod exist? Because many parts are not diameter-limited. A linkage, a pushrod, a brace, or a locating pin often has room for a solid section, and there the rod wins on everything else: it cannot be crushed by a clamp or a fitting, its ends can be bonded, pinned, or machined without reinforcing, it tolerates handling and drilling, and it costs less to produce. Choose the tube when diameter is fixed and weight is critical; choose the rod when the part needs to be fitted, fastened, and forgotten.

How rods are made, and why it matters

Solid carbon rods are pultruded: fibers are drawn through resin and a heated die, so the fibers run straight along the rod. That gives the rod its axial stiffness and strength, and it also defines its limits. Loads along the length are what it is built for. Side loads at a point, crushing clamps, and tight bends are not; if the application involves those, the design should spread the load with a fitting or sleeve rather than asking the rod to take it bare.

Where rods earn their place

  • Linkages, pushrods, and control runs in UAV, model engineering, and robotics
  • Bracing and support members in lightweight frames and structures
  • Pins, shafts, and locating elements in small precision equipment
  • Spars and stiffeners in sports and recreation equipment
Carbon fiber tubes in graduated diameters, shown for comparison with solid rods
Know the alternative. If the design can accept a larger diameter, a tube (shown here) may carry the same load at less weight. If it cannot, the rod is the dependable choice.

What to specify

Diameter, finished length per piece, and quantity are the core of the order; rods are cut to your length before shipping. Two more details are worth stating because they change how the rod is prepared: how the ends will be used (bonded into a fitting, clamped, left plain), and whether many pieces repeat in a production run or this is a one-off. The most requested diameter has its own page: the 8mm carbon fiber rod, a standard size for linkages and small structures.

A note on cutting and handling

If you cut rod on site, treat it like a composite, not a metal bar: a fine abrasive or diamond blade, support close to the cut so the end does not splinter, and dust extraction rather than breathing what comes off. Factory-cut lengths arrive finished, which is one more reason to order the length you need rather than stock to cut down.

Order rod by diameter and length

The rod product page covers ordering and the fitting questions. Diameter, finished length, quantity: that is the whole inquiry.

Home / Resources / What Does 3K Mean?
Explainer · Resources

What Does 3K Mean in Carbon Fiber Sheet?

Almost every carbon fiber sheet and tube on the market is described as 3K, and almost nobody outside the industry can say what the K counts. The short answer: it counts filaments. The longer answer explains why 3K became the default look of carbon fiber, and when a different tow size is the better engineering choice.

3K woven carbon fiber tubes showing the checker pattern of 3K tows
The 3K checker. Each square of the pattern is one tow: a bundle of three thousand filaments, woven over and under its neighbours.

The number counts filaments in a tow

Carbon fiber is produced as filaments far finer than a human hair. Filaments are gathered into bundles called tows, and the tow size is named by how many filaments it holds: 1K is one thousand filaments, 3K is three thousand, and larger tows such as 12K hold twelve thousand. When a sheet is described as 3K, it means the fabric was woven from 3K tows. It is a description of the fabric's building block, not a grade, a strength rating, or a quality mark.

Why 3K looks the way it does

Weave a fabric from 3K tows and each tow is wide enough to read clearly in the finished surface: the familiar checkerboard of small, even squares in plain weave, or the diagonal pattern of 2×2 twill. Finer 1K fabric weaves a much smaller, tighter pattern that reads almost as a texture. Heavier tows make a bolder, larger pattern and a fabric that builds thickness faster. When people picture "carbon fiber", they are usually picturing 3K, because it sits in the middle: fine enough to look precise, bold enough to be unmistakable.

Stacked carbon fiber sheets showing the 3K woven surface at different scales
Pattern at sheet scale. On a flat sheet the 3K pattern stays regular across the whole panel, which is why it is the default for visible parts.

What tow size changes, and what it does not

  • Appearance: tow size sets the scale of the visible pattern. This is the biggest practical difference on a finished part.
  • Drape: finer tows weave into fabric that follows curves and corners more easily; heavier tows prefer flatter geometry.
  • Layup work: heavier tows build thickness in fewer layers, which suits thick structural laminates where the surface is not the point.
  • Not strength by itself: the strength of a sheet comes from the fiber, the layup, and the manufacture together. A 3K sheet is not automatically stronger or weaker than a 12K one; they are built for different jobs.

When 3K is the right choice

For visible panels, covers, tubes, and parts where the carbon surface is part of the product, 3K is the safe, standard answer: the pattern customers expect, fabric that handles well in layup and wrapping, and wide availability. For deeply curved parts, a finer tow may follow the shape better; for thick structural plate that will never be seen, heavier tows can be the economical route. If the part is visible and roughly flat or gently curved, the conversation can honestly end at 3K, which is why it is the default across our sheet and roll-wrapped tube ranges.

3K is the standard surface on our sheets

Plain and 2×2 twill, matte or gloss, cut or machined to your drawing. The sheet page carries the options.

Home / Resources / CNC Machining Carbon Fiber
Process Guide · Resources

CNC Machining Carbon Fiber: What Makes It Different

Carbon fiber sheet becomes useful parts on the CNC: frame plates, mounting panels, covers, brackets. The machining itself is routine for a shop set up for composites, and genuinely troublesome for one set up only for metal. This guide explains what is different about cutting carbon fiber, and what you can do in the drawing to get parts that arrive right.

CNC machine cutting a carbon fiber plate
Cutting plate in-house. The machine is familiar; the material behaviour, tooling, and dust are not the same as metal.

It is abrasive, and it eats the wrong tools

Carbon fibers are extremely hard on cutting edges. Tools that would run for weeks in aluminium dull quickly in carbon laminate, and a dull tool stops cutting cleanly and starts tearing, which shows up as frayed edges and delamination around holes. Composite work uses tooling chosen for abrasion resistance, typically diamond-coated or solid carbide tooling made for the material, and treats tool condition as a quality variable, not a consumable to stretch.

The dust is the real problem

Machining carbon fiber produces a fine, conductive dust rather than chips. It has to be extracted at the source: it is unpleasant to breathe, it settles into machine electronics and causes faults, and it contaminates other work in the shop. A composite-ready workshop runs extraction as part of the process and keeps carbon work segregated. This is the single clearest test of whether a supplier actually machines carbon fiber regularly or is improvising with a metal shop.

CNC waterjet cutting a carbon fiber sheet at the Justar factory
Waterjet is the other route. For sheet profiles, waterjet cutting avoids heat and tool wear entirely, and leaves an edge that needs little finishing.

Edges, holes, and delamination

A laminate is layers, and machining can separate them if it is done badly, most often where a drill breaks out of the back face or a cutter exits an edge. Good practice supports the work properly, chooses entry and exit strategies that keep the layers compressed, and finishes edges so the part does not start life with a lifted layer. When you receive machined parts, the edges and hole exits are where quality shows first: they should be clean, sealed-looking, and free of fuzz or lifting.

What helps in the drawing

  • Generous corner radii where the design allows: cutters are round, and sharp internal corners cost time or cannot be made at all
  • Holes sized for the fastener plus a sensible clearance, with edge distances that respect the laminate rather than treating it as sheet metal
  • Tolerances called out where they matter, and left open where they do not; composite plate is not ground steel, and pricing follows the tolerance you demand
  • The finished faces identified, so finish work is spent where it will be seen
Finished CNC machined carbon fiber parts
Finished parts, not blanks. Machined, drilled, and edge-finished in the same factory that made the sheet.

Why machining sits with the material maker

When the factory that produces the sheet also machines it, the layup can be planned around the part: thickness, surface layer, and machining allowances decided together, and any issue found at the machine is answered by the people who made the material. It also removes a shipment and a hand-off from the middle of the job. Our forged carbon sheet exists for exactly this route: stock made to be machined into finished parts, by us or by your own shop.

Stock made to be machined

The CNC-ready forged carbon sheet is supplied flat and consistent for machining, or machined into finished parts in our own workshop.

Home / Resources / Carbon Fiber Cost and Pricing Guide
Buying Guide · Resources

Carbon Fiber Cost and Pricing Guide

Ask two suppliers for the same carbon fiber part and the quotes can land far apart, with both of them honest. The reason is that "carbon fiber" is not one material at one price; the cost of a finished part is built from the material form, the layup, the curing route, the machining, and the quantity, and each of those can move the total more than the fiber itself does. This guide explains where the money goes, so you can read a quote and design a part that does not pay for what it does not need.

Carbon fiber production line running at the Justar factory
Cost is set on the production floor. Material form, layup labour, curing, and machining all happen here, and all of them are in the quote.

Driver 1: the material form

Raw fiber becomes fabric, prepreg, sheet, tube, or profile, and each step adds cost while saving you work. A woven sheet costs more per kilogram than the fiber in it, and less than the finished part cut from it. Pre-impregnated material, with resin already in the fabric, costs more than dry fabric and wet layup, and returns consistency and performance for it. Forged and compression-moulded stock carries moulding cost. None of these is "the expensive option" in the abstract; the question is always which form puts the fewest paid hours between the material and your finished part.

Driver 2: the layup and the curing route

Layers are placed by people or by process, and cured by heat, pressure, or both. Autoclave curing produces the most consistent, highest-quality laminates and is the most expensive route per part. Simpler press or oven cures cost less and are entirely adequate for many industrial parts. Wet layup is the cheapest entry and the least repeatable. When a quote seems high, ask which curing route it assumes; when a quote seems low, ask the same question. The route is a legitimate design decision, not a detail.

Driver 3: machining and finishing

On machined parts, machine time is frequently the largest single cost after the material. Tight tolerances, sharp internal corners, many small holes, and cosmetic finishing on every face all add minutes that become money. The economical part is designed for the cutter: sensible radii, tolerances only where they matter, finish specified where it is seen. A short conversation with the factory before the drawing is frozen routinely finds these savings; after it is frozen, it cannot.

Carbon fiber sheet coming off the production line at the Justar factory
Repeatability is a cost lever. A part that repeats across orders spreads its setup, tooling, and learning over every run.

Driver 4: quantity, honestly assessed

Setup, tooling, and process learning are real costs that a first order carries almost alone and a repeat order barely notices. Prototypes are therefore expensive per piece in a way that says nothing about the production price. The useful conversation is two numbers, not one: the price for the samples you need now, and the price at the volume you realistically expect. Designing and quoting for a fantasy volume produces a fantasy price; designing for the real ramp produces a part that survives contact with purchasing.

Driver 5: who you are buying from

Every intermediary between you and the production floor adds a margin and removes information. Buying from the factory removes the trading margin, and, just as valuable, it removes the telephone game: the person quoting your part can walk to the machine it will be made on. When quotes differ widely, compare what each one actually includes (material form, cure route, machining, finishing, inspection) before comparing the totals; the cheapest line often turns out to be a shorter list.

How to keep a carbon project economical

  • Start from standard forms (sheet, tube, rod, profile) and customise dimensions before customising everything
  • Match the curing route and material grade to the actual load case, not to the best available
  • Design for the cutter: radii, sensible tolerances, finish where it shows
  • Quote prototype and production quantities separately, with a realistic ramp
  • Buy from the maker, and compare quotes line by line, not total by total

Get a quote built from your actual part

Browse the product lines, then send the drawing or dimensions. The factory quotes the material form, route, and machining your part actually needs, with no trading margin in between.

Home / Resources / Carbon Fiber in Drones and UAV
Applications · Resources

Carbon Fiber in Drones and UAV

Of all the places carbon fiber is used, the drone airframe is where its case is easiest to make. An aircraft has a hard weight budget: every gram carried by the structure is a gram taken from the battery, the motors, or the payload, and flight time is bought with grams. Carbon fiber's stiffness at low weight is exactly the trade an airframe wants, which is why it moved from racing drones into inspection, mapping, agriculture, and industrial UAV platforms.

Carbon fiber UAV X-frame seen from above, machined from carbon plate
The classic X-frame. Arms, body plates, and motor mounts machined from carbon plate, assembled with standoffs and fasteners.

The frame: machined plate does most of the work

The typical multirotor frame is a small structure of flat parts: body plates, arms, and motor mounts, cut from carbon sheet on a CNC and stacked with standoffs. Plate construction suits drones because the geometry is mostly flat, the parts are easy to replace after a crash, and the same sheet stock serves a whole family of frame sizes. Stiffness matters here beyond simple strength: a frame that flexes confuses the flight controller and wastes energy in vibration, so the plate's job is to be rigid first and light second, and carbon sheet does both in thicknesses that would be flimsy in plastic and heavy in metal.

Tubes and rods: arms, booms, and linkages

Larger and folding designs move from plate arms to tube arms, where a roll-wrapped tube gives a stiff, round arm that can fold, telescope, or carry wiring inside. Rods appear in the small, hard-working places: linkages, landing-gear elements, antenna and payload supports, and control runs, anywhere a short, stiff, light member is needed and a fitting has to grip it. The choice between a plate arm, a tube arm, and rod linkages is a design decision about size, folding, and repair, and a working UAV usually ends up using all three forms.

Carbon fiber drone frame at an angle showing stacked plate construction
Stacked and bolted. Plate construction keeps the frame repairable: a damaged arm or plate is replaced, not the whole aircraft.

Beyond the frame

  • Payload structures: camera and sensor mounts, gimbal plates, and equipment decks where vibration and weight both matter
  • Fixed-wing UAV: wing spars, fuselage tubes, and tail booms, where long, stiff, light members decide the aircraft's range
  • Ground and support equipment: launch rails, transport frames, and antenna masts built from the same tube and profile stock
  • Protective parts: motor guards, battery trays, and enclosures machined from sheet
Close-up of a machined carbon fiber drone frame plate with fasteners and cut-outs
Detail decides durability. Clean cut-outs, correct hole finish, and edges that do not delaminate are what separate a frame that survives seasons from one that survives a month.

What to specify when you order UAV parts

For frame plates: the drawing, the sheet thickness your design assumes, and whether you want raw cut parts or finished, edge-treated parts ready to assemble. For arms and booms: tube diameters, wall or inner diameter, lengths, and how the ends join the frame, because clamping and folding joints decide whether a tube should be roll-wrapped. For repeat supply, say so at the start: frame parts for a production UAV are a repeatability exercise, and the factory will set the job up that way from the first batch.

Building or supplying a UAV?

Frame plates come from our sheet range, arms and booms from the tube range, both machined and supplied by the same factory.

Home / Resources / Wet Carbon vs Dry Carbon
Explainer · Resources

Wet Carbon vs Dry Carbon: What the Terms Actually Mean

"Wet" and "dry" are the two words most often used, and most often misused, to describe how a carbon fiber part was made. They do not describe the part's finish, its gloss, or whether it feels dry to the touch. They describe when the resin met the fiber, and that one difference drives the part's consistency, weight, cost, and appropriate uses.

Layup workshop at the Justar factory, where carbon fiber material is laid up before curing
Layup is where the routes divide. Whether the fabric arrives already carrying its resin, or meets the resin on the table, decides almost everything downstream.

Wet carbon: resin applied during layup

In wet layup, dry fabric is placed in or on the mould and liquid resin is worked into it by hand or with simple equipment, then the part cures, often at room temperature or with modest heat. It is the oldest and simplest composite route: low tooling cost, little specialised equipment, and complete freedom of shape. Its limits are consistency. How much resin ends up in the part depends on the operator, excess resin adds weight without adding strength, and voids and dry spots are hard to eliminate entirely. For one-off parts, prototypes, repairs, and large simple shapes, those limits are often an acceptable price for the route's simplicity.

Dry carbon: prepreg, compacted and cured under pressure

"Dry carbon" is the trade's shorthand for parts made from prepreg: fabric that arrives already impregnated with a precisely measured amount of resin. The layup is placed, vacuum-bagged or moulded, and cured with heat, in higher-end work inside an autoclave under pressure. Because the resin content is set at the material factory rather than at the bench, and pressure squeezes out voids and excess resin, the finished part is lighter for the same strength, more consistent from part to part, and cleaner in surface and structure. The costs are real too: prepreg material is more expensive, needs cold storage and careful handling, and the curing equipment is a serious investment.

Autoclave with its door open at the Justar factory
The autoclave end of the scale. Heat and pressure curing is what turns prepreg layups into the most consistent laminates the process can make.

How to tell which one a part is

  • Weight for the size: a dry-carbon part is noticeably light for its stiffness; excess resin makes wet parts heavier than they need to be
  • Surface and edges: prepreg parts show a crisp, even weave and clean edges; wet layup often shows resin-rich patches, pinholes, or uneven gloss
  • Consistency: order ten of each; the dry-carbon parts will match each other closely, the wet ones will vary
  • Honest paperwork: a maker who uses prepreg and autoclave curing will say so plainly, because it is the expensive route and it is the point

Which one should your part be?

Choose by what the part must do. Structural parts, repeat production, weight-critical assemblies, and anything a customer will inspect closely belong on the prepreg side of the line, and the price difference is the cost of consistency. Prototypes, one-off shapes, repairs, and parts whose job is shape rather than structure can be honest wet-layup work. The failure mode to avoid is paying dry-carbon prices for wet-carbon manufacture, or the reverse, expecting autoclave consistency from a bench process. Ask the maker which route the quote assumes; a factory will answer directly, and the answer tells you most of what you need to know about the part you will receive.

Our sheets are the consistent end of the line

Controlled layup and curing, supplied as stock or machined parts. The sheet page sets out the weaves, finishes, and processing options.

样本说明:本样本为 justarcb.com 多页重建稿,供确认后上线,现站未动。页面结构对应正式站路径(首页、/products/、7 个产品页、/carbon-fiber-application/、/capabilities/、/contact/),并保留已收录的 /carbon-fiber-rod-8mm/ 与碳纤维护甲指南页。全站只用 Justar 主体,不展示供应商。首页已去掉旧的 SEO 体检段与未核实的年限、项目、国家数字。询盘发往 [email protected],WhatsApp +86 17076247612。产品图片取自现站 justarcb.com。制造能力页与首页制造流程区已加入 10 张工厂实拍图(车间全景、生产线、卷材上料、铺层车间、热压罐、CNC 切割),只用 Justar 名义,未用任何带公司名、地址、证书的图,也未用带公司大字的工厂外景图。页头与页脚已换成原蓝色条纹 JUSTAR logo:页头浅色底用蓝色版,页脚深色底用白色版,两版图片均已存入样本本地,不再外链。Logo 已定为原版:页头用蓝色条纹版,页脚深色底用白色版。本轮新增 Resources / Blog:导航已加 Resources,总页 /resources/ 列 9 篇文章卡片(8 篇新文章 + 已有护甲指南),每篇独立成页、配 2 到 3 张图、文末链回对应产品页,文章只写实在内容,未编规格、未写未核实数字和具体价格。产品页补图均按指定素材下载存入样本本地后引用,没有直接外链:板页加板图,管页加管图,3K 哑光卷制管页加 3K 管图,型材页加型材图,CNC 锻造板页加无人机架图和板图,伸缩话筒杆页加带接头的管图,应用页加无人机架图。杆图缺口已补:裁剪版杆图已由工作区原文件存入样本本地(assets/rod1-clean.jpg),杆页、8mm 杆页与 Blog 杆指南卡片均已换上该图。另一处素材缺口:无人机架图 2 的源图在阿里 CDN 已失效,只返回 No Photo 占位图,未使用,其余 3 张无人机架图正常。